How to Self Program Starkey HA's

Hearing Aid Self-Fitting and Adjusting [DIY]
#6

Hi Russ,
The sound after my one foray into programming was much better than what had been on the HA’s. One of the reasons for that is that I had replaced the HA tubes/speakers from 40 to 50 and never re-programmed because of the expense of going to a Dispenser. I’m easy to please and so am satisfied with the defaults. Once you plug in your numbers manually to the software, the software will walk you through the steps. My HA’s are a bit older, WI110’s. Your Muse probably have more capabilities. I have not been back to re-visit or further adjust the HA’s.
I did not re-set back to factory settings.
I also saved previous sessions, but what I have now is far superior to what was programmed prior.
Tell me about the book you sent for. The software can be daunting if you stay from the suggested settings. It would be nice to understand the verbage better and perhaps try some other settings. Check out the video I just posted. When I watched it I was impressed with the fact that Starkey software programs differently depending on whether the user has had HA’s for a while or is a new user.
Please post any tips. I was really afraid that I’d screw up my HA’s, but it went very well.

  • Allen
#7

Hi Allen,

I have watched the video you mentioned above. I actually watched a couple because they had basically the same thing for 2016, 2015, etc. and I had watched one before I saw the year thing. The software is pretty well setup, but like you mentioned, once you get away from the initial settings, there are other parts where it seems to become quite difficult or at least harder to understand.
The book I bought is Hearing Aids by Dillon Harvey. Should have it in a day or two. I bought an older used version from ebay for $19.00 because the new one is about 80-90 dollars and I figured there probably wasn’t a whole lot of difference. I don’t need all the information, just enough to point me in the right direction. It has gotten good reviews from Audiologists in that section of this forum, so we’ll see. I don’t want to do too much till I get it and at least thumb through the book.
I will let you know what I think of it as soon as I get it.

It’s good to hear that things went well on your initial programming. That gives me a bit more confidence. :slight_smile:

#8

Hi, I use Halo 2 I1600 hearing aids and will soon read out the set-up of hearing aids using a Trulink programmer and the Inspire software 2018 and would like to learn how I can perform a fine tuning (basic set-up by hearing care professional is done) independently. Does anybody have any personal experience here and could give me support?

#9

I can’t get into a lot of details but you had your HA programed by your Audiologist so you will need to record the test and current settings into the Patientbase. After Trulink has connected to your HAs by selecting "Read Device Settings" and then Start"
Disconnect Trulink and you will have the option to record settings in to your database. This way you can always get back to where you started from.
xoff

Now you can connect again.
On the right side under Pre Fitting select "Inspire online" and scroll down to "What’s new in Inspire X" “Latest Quick Tips” in the Training Corner you will find “Patient Adjustment Guide” pick the one for your HAs and start from there.

Explore the rest of the settings and options

Have fun.

1 Like
#10

Hi Flatfish, Thank you very much, that’s the starting point that I thought was important to not lose the base set-up. Could you give me a brief explanation of how I can restore the original settings in the hearing aid profiles after adjustment if necessary. With these quick guides, I would be very well prepared to familiarize myself with the possibilities of fine adjustments via Inspire. Many Thanks

#11

Asked and answered many times. Use the search magnifying glass. For example;

Here, and Here, and Here.

Test it first with different session names before you make any changes.

#12

Load
Load.JPG1418×770 59.9 KB

From that screen Pick Load Previous Session and it gets you in the PatientBase
Note on the inspire program after you made any changes it will reflect immediately in the HA so you can hear how you changed it. I will not go through a SAFE function, the change will remain in your HAs. When you disconnect from the Trulink it will give you an option to safe those settings to the PatientBase if you want but the HAs will not automatically go back to the previous settings.

#13

Thank you again, now I feel well prepared, have also found the training videos in the Inspire software environment. As soon as I receive the TruLink Programmer, I will try my best and know now that nothing bad can happen if I follow your basic statements.

#14

Are you sure? I don’t have Inspire loaded, but in general, at End/Save time you get a choice to save to Database, Save to Hearing instruments, Save to both, or Save to none.

Yes the fitting changes are reflected in the hearing instruments as you make changes during the fitting. However, if you don’t save those changes into the hearing instruments at the End/Save step then your hearing instruments revert back to the previous settings.

Otherwise what would be the point in saving to hearing instruments?

It’s very easy to test.

  1. Make one small change to the gain in one of your frequencies.
  2. Write it down so you don’t forget it.
  3. Don’t save anything at the End/Save step

Start over, use Read Device Settings. You small change should be gone and it should revert back to the original setting before your small change.

#15

When you start you choose hearing instrument or database session;
c0

At Save time you can save to database session AND hearing instruments or neither;

c1

At Save time if you click NO, or cancel, or if your computer dies, Inspire should not inadvertently save the changes to your hearing instruments. That would be a big whoops! You can test this real easy as stated above.

#16

I am on Inspire X 2018.xxxx Maybe there is a difference.
on the first picture I just selected read device settings and increased the 2500HZ from 89 to 97 on the loud (heavy black line)

Capture

I then Disconnected Surflink (Picture in previous post with the red arrow on the X)
Now My HAs are disconnected from Surflink.
Under Save Fitting I selected No

Capture4

I now reconnected again and selected Read Device Settings and that’s what I get. It Remembered the settings without me saving them.
I don’t think it’s good since if you want to go back before you made changes you have to go back to the patientBase and retrieve the settings.

But the text in the SAVE FITTING box is pretty clear now.

Capture2

#18

Yikes, I am surprised that it saves whatever you were tinkering with. Are the changes still there after you open/close the battery doors on the hearing aids.

#19

Yes the changes are still there after open/closing the battery doors. I just tested it to make 100% sure.

I have been programing my HAs for a while now and have not found another way. At first I was looking for the save button and could not find one so finally figured out that it automatically saved the adjustments to the device (HAs) as the Save Fitting Window spells out.

#20

What ever change you made automatically saved in HA taht saving option only for storing session data on computer. And not on ha you have to manually restore old session data into ha

1 Like
#21

Hi Guys… I’m in trouble. Just two days ago the link was working. Now it’s not… I think it was removed permanently. Does anyone have a copy laying around for the inspire x? I greatly appreciate it. Thanks.

#23

@PVC I love your sense of humor :slight_smile: I’ve got the fitting software i need. Installed and running. Thanks to a member of this forum. Now I just need the surflink programmer. These are hard to find for some reason aint that right? But the HA’s I have now require black boots 312 as shown on pda chart somewhere on this forum. These are for Z series i110 ric 312. if I decide to go the hipro usb route with cables that what I need unfortunately those boots are hard to acquire as well. All other colors are available for sale online and of course on ebay I don’t know why the black one isn’t. I even asked the seller who sold other colors and he said “no”. Again I love your sense of humor. I really prefer the surflink programmer due to its ease of use and no wires. I would like a ball park figure with shipping included or if one of the dispenser is willing to sell to me locally. Whichever works… Help is greatly appreciated. I even post on the salespage if someones out there is selling one let me know. Thanks in advance.

#24

You must mean SAVE, and not SAFE.

#25

Looks like the FTP site no longer has a copy of the software at that address, and I am unable to find any torrents. Does anyone have a copy that they would share? If you have a copy, I can arrange a secure upload site.

#26

Hello all,

New visitor to this site.

Newer user of Livio AI’s. Not overjoyed with depth, quality and responsiveness of local support. I am technical. I am thrilled to learn that there are tools available that allow me to adjust profiles.

I can provide a detailed experience with the Livio’s, as I had compared them against 6 other options of varying price and functionality levels. Overall, while imperfect, they remain as the most fully featured devices of which I am aware.

Thank you for this community, and for all who share their expertise and wisdom.

2 Likes
#27

Hey new to self programming and need the new inspire software for my Starkey livio ai 2400. Thank you in advance any who can help me out. And also maybe direct me to getting hearing care anywhere set up to send setting to phone and skip nohalink