Depends on the hearing aid. Some aids you take old receiver out - pop new one in. Others are a very difficult to remove too due to limited space/tight fit. Others aids are only replaced at HA repair outlets by the HA manufacturer. Bottom line most people that use a hearing aid are going to let someone else (more experienced) replace receivers when time comes. Especially the elderly.
1 Like
I suspect you are including BTE hearing aids. This thread is about RIC hearing aid receivers.
Receiver replacement on RIC hearing aids is not complicated.
I have experienced two receiver failures. The first was about 5 years ago when I was wearing Starkey HAs that I purchased from an independent aud. The receiver when completely dead. The Audi charged me $90 and it took two weeks for the factory turnaround.
The second failure was with my COSTCO Resound HAs. The receiver slowly started to sound diminished and I could hardly hear the start signals when inserting the receiver in my ear. I went to COSTCO and they tested the receiver and immediately replaced it on the spot and did not charge me anything. A great experience with COSTCO service.
1 Like
I woke up to a lively forum.
Sorry if I posted in the wrong forum. I did post in Octicon but now I see it is in the general hearing aid forum. I am using a BTE with receiver in the ear. As someone mentioned, I push & pull the receiver/cable part when wearing or taking it out. I am now suspecting the receiver or even the cable connecting the receiver to the HA itself is faulty or became loose. Hence the issues I am having. I’ll ask my audi. He told me before the receiver usually lasts 2 years and he could change it with no problem if it fails. I just don’t know what happens if maybe the part where the cable connects to rhe receiver has gotten loose.
I should have mentioned that the Starkey HA receiver did have a loose wire at the point that the wire connects to the receiver. In the second case I mentioned, the receiver just went downhill in speaker performance over time, so I took it in to COSTCO for replacement.
You are describing a RIC hearing aid, not a BTE hearing aids. BTE hearing aids use sound tubes. Both type aids look similar but have differences.
2 Likes
Yes, RIC. My brain says RIC, my fingers type BTE. So I am guessing the connection of the tube with the receiver is somewhat loose? I emailed my audi to ask if there’s a way to troubleshoot to confirm this is the case. I want to say that the wax filter is clean. My audi checked it.
1 Like
RIC aids don’t have a tube. Your RIC aids have a wire from the aid to the receiver (speaker) that goes deep into the ear canal. These wires tend to be the weak point of RIC aids. The wire connection at the aid and at the receiver itself tend to get bent and pulled on from general use. The receiver itself is very reliable.
Oticon calls RIC aids RITE aids.
Can you show any evidence or white papers on why at “24 months”
Yes I agree, for a variety of reasons, not because it “wears out” or reaching a “24 month” timetable.
Why? Your swapping over to test and see if it’s the receiver or HA that has a fault, not for any other reason.
Murphy’s Law?
I agree.
Unfortunately the warranty doesn’t cover receivers by most manufacturers. Unless of course it’s a manufacturer fault to begin with.
Yes there is, just swap the receivers over to test if it’s the HA or receiver.
except for those embedded in a hard shell.
1 Like
The op could still remove the receiver from the HA and change it with the other side, just to test if it’s working as it should.
1 Like
Check out how easy it is to change the receiver in this link.
1 Like
I’ve replaced 2 R and 1 L ‘receivers’ on my just over 2 year old KS8’s in the last 8 months. All no cost even today with the local Costco implementing special operations due to the COVID19 virus. Only one person working in hearing center there. Anyway, I asked her why do these receivers fail. She said moisture. l do remove them by pulling on the wire. I’ll try removing them by pulling on the short plastic piece that loops inside the outer ear to help keep the aid in place. I’ve ordered another " Ezy Dose Dehumidifier" … my last one is over a year old and is due to be replaced.
Three separate Audi’s (all different firms) told me RIC (in my case in ear mold) last approx. two year, give or take. Now I never had that (short term) issue when I wore analog hearing aids with receiver in hearing aid body. Back then I could go 4, 5 years with no receiver problem. But when the receiver switch happened ten years ago (roughly) everyone was told you’d probably have to replace small RIC every 24 months. Some people dry their HA’s at night, others don’t. The group that doesn’t will probably be the first to have to replace receivers due to moisture issues.
Probably having a back up pair of receivers isn’t a bad idea, but I’d rather purchase new ones when my existing ones falter. Kudos to those that can swap out receivers on their own, do their own HA programming, and buy what ever on eBay without a second thought. Truth is 90% of all hearing aid users have a “hearing specialist” do all the above, of course at a higher cost. I’m really not here on HT to talk to the 10% that do their own HA repairs.
Regarding warranty, a savvy HA purchaser should inquire (and might demand) that HA receivers be replaced under a 3 or 4 year warranty for free. Wouldn’t it be nice if a warranty covered everything regarding a HA function and didn’t exclude x, y, z. But as you say most HA manufactures probably won’t replace receivers unless they fail during the first twelve months of operation.
1 Like
For ReSound Quattro’s, the receiver wire is an integral part of the receiver. I seem to recall that a special tool is required/recommended to detach the receiver wire (and receiver) from the body of the hearing aid. If anyone has recommendations on where to get the tool or what to use in its stead, I’d be happy to hear them. But swapping receivers on HA bodies, if you have the tools to do it, would be a good way of distinguishing body circuitry failure vs. receiver failure as tenkan suggested above.
On testing receiver performance, I’ve found that I can do a crude job by playing tones from an Android tone generator app into over-the-hear headphones one ear at a time vs. streaming the same tones one ear at a time to my HA’s. Since both receivers are unlikely to fail to the same degree in both ears at the same time, one ear serves as a “control” or reference point for the other ear, which you may perceive to be doing worse, etc.
If you’re into DIY, you can always use in-situ audiometry as a built-in test of how your receivers (and HA circuitry) is performing. If you’ve had a recent audiogram and your HA’s have been appropriately programmed for that audiogram, the in-situ audiometry audiogram should relatively closely reflect your audiogram done by conventional means - that tests amplification of low-level sound into a range that your hearing can just detect. If you use the in-situ audiometry feature for evaluating the discomfort level of maximum volume sound, that can very grossly test whether your receivers are still capable of producing output so loud it’s uncomfortable. I have moderate-to-severe age-related high frequency hearing loss, both ears are about the same, and sound frequencies across entire range that HA’s typically address is more or less “recoverable.” Such a strategy is obviously not going to work very well for more complicated or much more severe hearing loss and obviously if you can’t play around with DIY, the in-situ audiometry will not be an option. But the tone generator tests initially suggested might at least give you an idea how well or badly your HA’s are currently performing and if you have an essential job, e.g., nurse in an ICU, maybe you could find an audiologist or HCP somewhere in recognition of your dedication to society who would service your HA’s if you can’t figure out and fix your HA’s yourself.
1 Like
Be sure the wax guard is clean, and when replacing it look closely for a bit of hard wax that may have got past it and can block the sound.
2 Likes
Your initial hearing aid aids must’ve been out of warranty. My audi has changed the receivers for free but under the warranty period.
One of my hearing aids conking out completely while I was doing…nothing, basically, just out shopping. Came home, took it out, let it sit a few hours and I was back in business. A few weeks later, same thing as I was sitting quietly and suddenly realized I wasn’t hearing out of my right ear. Called the Costco fitter, and he said could be wax. So I pulled off the dome, wax guard nice and white, ran a fingernail over the top of the dome - and I was hearing again. Apparently warmth of the ear can cause the wax to soften and gunk things up a bit. Nice to know that sometimes it’s something that simple.
My domes exit through two side-holes in a bump on the end. I too have had total silence cured by fooling with the dome. I think this is why my fitter gave me a piece of plastic fishing line. It may actually be for the tube, but it is a nice fit in the dome exits. (Go to the dollar store and get the strongest readers they have so you can see the hole.)